Teledyne 200A Uživatelský manuál Strana 16
- Strana / 225
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Teledyne API Model 200A NO
X
Analyzer Instruction Manual, 02246, Rev. G, DCN 5247
1 HOW TO USE THIS MANUAL
The Model 200A has been designed to provide serviceability, reliability and ease of operation.
The M200A's microprocessor continually checks operating parameters such as temperatue, flow,
and critical voltages. The instruments modular design uses captive screws to facilitate repair and
ease of access. If you encounter any difficulty refer to Section 9 General Troubleshooting Hints.
We recognize that the need for information in this manual changes as time passes. When the
instrument first arrives, it is necessary to get it up and running quickly and verify its correct
operation. As time passes, more detailed information is often required on special configurations,
calibration alternatives and other operational details. Finally there is the need for periodic
maintenance and to quickly troubleshoot problems to assure maximum reliability and data
integrity.
To address these needs, we have created three indexes to the information inside. They are:
Table of Contents:
Outlines the contents of the manual in the order the information is presented. This is a good
overview of the topics covered in the manual. There is also a list of Tables and a list of Figures.
Index to M200A Front Panel Menus:
The Menu Index (Table 5-5-1 and Table 5-5-2, Table 5-5-3 and Table 5-5-4) briefly describes
the front panel menus and refers you to other sections of the manual that have a detailed
explanation of each menu selection.
Troubleshooting Section 9:
The Troubleshooting Section, outlined in the Table of Contents, allows you to diagnose and
repair the instrument based on variables in the TEST menu, the results of DIAGNOSTIC tests,
and performance faults such as excessive noise or drift. The troubleshooting section also
explains the operation, adjustment, diagnosis and testing of each instrument subsystem.
If you are unpacking the instrument for the first time, please refer to Getting Started in
Section 2.
1-1
PRINTED DOCUMENTS ARE UNCONTROLLED
- TELEDYNE 1
- HIGHLIGHTS 2
- MODEL 200A 4
- NITROGEN OXIDE ANALYZER 4
- SAFETY MESSAGES 6
- TABLE OF CONTENTS 8
- LIST OF FIGURES 12
- LIST OF TABLES 13
- 1 HOW TO USE THIS MANUAL 16
- 2 GETTING STARTED 18
- 2.3 Initial Operation 23
- WARRANTY 32
- 3.3 Warranty 34
- TERMS AND CONDITIONS 35
- 4 THE M200A NO 36
- ANALYZER 36
- 4.2 Operation Summary 38
- 4.2.4 V/F Board 39
- 4.2.5 Front Panel 39
- 4.2.6 Power Supply Module 41
- 4.2.8 Ozone Generator 44
- 4.2.9 Molydbenum Converter 44
- 5 SOFTWARE FEATURES 46
- 5.1.1 Sample Menu 49
- 5.1.2 Set-Up Menu 50
- 5.2 Sample Mode 53
- 5.3 Set-Up Mode 59
- 5.3.4 Range Menu 61
- 5.3.5 Password Enable 65
- 5.3.6 Time of Day Clock 65
- 5.3.7 Diagnostic Mode 65
- 5.3.8 Communications Menu 65
- 5.3.9 Variables Menu (VARS) 66
- 5.4 Status Output 67
- 5.5 RS-232 Interface 68
- 5.5.2 Command Summary 73
- 5.5.8 Internal Variables 84
- 6.1 Rack Mount Options 86
- 6.2 Zero/Span Valves 86
- Mode No. Mode Name Action 88
- 6.5 Permeation Tube 90
- Zero/Span Valves Option 99
- NO and NO 101
- 7.6 Calibrate on NO 102
- Permeation Tube 102
- Closure 104
- 7.8.3 Data Recording Device 108
- 223 ONOONO 109
- = analyzer flow demand (cm 110
- /min (110/100) = 550 cm 111
- = 500 cm 111
- 7.8.7 Calibration Frequency 120
- 7.8.10 ZERO and SPAN Checks 123
- 7.10 Calibration Quality 128
- 7.11 References 130
- 8 MAINTENANCE 132
- Teledyne API Model 200A NO 142
- 8.9 Leak Check Procedure 146
- (table continued) 151
- 9.2 Performance Problems 173
- 9.2.1 AC Power Check 174
- 9.2.2 Flow Check 174
- 9.2.4 Negative Output 176
- 9.2.5 Excessive Noise 176
- 9.2.6 Unstable Span 177
- 9.2.7 Unstable Zero 178
- 9.2.8 Inability to Span 178
- 9.2.9 Inability to Zero 179
- 9.2.10 Non-Linear Response 180
- 9.2.11 Slow Response 181
- 9.3.2 RS-232 Communications 185
- *Required settings 191
- 9.3.4 Status/Temp Board 194
- 9.3.5 Power Supply Module 196
- C. The 200
- 9.3.6 Ozone Generator 201
- 9.3.7 Flow/Pressure Sensor 204
- 9.3.8 NO 209
- Sensor Module 209
- 9.3.10 Pneumatic System 214
- 10 M200A SPARE PARTS LIST 216
- Part No. Description 217
- Includes: Qty 220
Související produkty a manuály pro Měření, testování a kontrola Teledyne 200A
(371 stránky)
(42 stránky)Makita HR4500C (MJ) manuales
Manuales del propietario y guías del usuario para Herramientas Eléctricas Makita HR4500C (MJ).
Ofrecemos 1 manuales en pdf Makita HR4500C (MJ) para descargar gratis por tipos de documentos: Manual de usuario
Komentáře k této Příručce