Teledyne 300EU Uživatelský manuál Strana 49
- Strana / 94
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
M300EU CALIBRATION PROCEDURES
(Addendum to M300EU Manual - P/N 04145)
7. CALIBRATION PROCEDURES
Calibration of the M300EU should be performed according to the procedures described in Chapters 7 & 8 of the
M300E/EM Manual - P/N 04288 with the following notes and exceptions:
• Delivering span and zero gases for the higher resolution the M300EU can be difficult. Attention must be
paid to the quality of the gasses, the level of contaminants in the gases as well as the history and
conditioning of the gas delivery components.
• The analyzer must be continually operating with and adequate flow of sample gas, for 2 hours prior to
performing a calibration (12 hours is recommended for the initial calibration).
• DO NOT calibrate the analyzer if it has been turned off or if no sample gas has been flow though it
within the last 2 hours.
• After this stabilization period is complete and just prior to performing the initial calibration, force the
instrument to perform an auto-reference measurement by following the instructions in Section 6.4.2 .
REQUIRED EQUIPMENT, SUPPLIES AND EXPENDABLES
• Gas lines to and from the analyzer should be PTFE or FEP Teflon, glass, stainless steel or brass only.
• Zero-air source (defined in Section 7.1.2 of the M300E/EM Operators Manual).
• Zero air must include at least 5% O
2
(required for the proper operation of the CO scrubber).
• If a zero air generator, such as the Teledyne Instruments M701, is used it
MUST be equipped with a
hydrocarbon (HC) & CO scrubber option. For the Teledyne Instruments M701, this is Option 2B.
• Span gas source (defined in Section 7.1.3 of the M300E/EM Operators Manual).
• A recording device such as a strip-chart recorder and/or data logger (optional). Data recording device
should be capable of bi-polar operation so that negative readings can be recorded.
• For electronic documentation, the internal data acquisition system can be used.
NOTE
If any problems occur while performing the following calibration procedures, refer to Chapter 11 of this
manual for troubleshooting tips.
MANUAL CALIBRATION
The information found in Section 7.2 of the M300E/EM Operators Manual (P/N 04288) is applicable to the
M300EU with the following exception(s).
• STEP3 – ZERO/SPAN CALIBRATION
• Set the display to show the STABILITY test function (same as the CO STB function mentioned in the
M300E/EM operator’s manual).
• There is no GAS TO CAL step because the M300EU cannot be modified to include the O
2
and CO
2
sensor packages.
MANUAL CALIBRATION CHECKS
The information found in Section 7.3 of the M300E/EM Operators Manual (P/N 04288) is applicable to the
M300EU with the following exception(s).
• Set the display to show the STABILITY test function.
05514 Rev A1 41
- MODEL 300EU 1
- SAFETY MESSAGES 3
- TABLE OF CONTENTS 5
- LIST OF FIGURES 6
- LIST OF TABLES 6
- LIST OF APPENDICES 7
- INTRODUCTION 9
- USER NOTES: 10
- WARRANTY 11
- GETTING STARTED 13
- 3.3. ELECTRICAL CONNECTIONS 14
- M300EU GETTING STARTED 15
- M300EU 16
- 3.4.2. WARNING MESSAGES 17
- 3.4.3. FUNCTIONAL CHECK 18
- 3.5. INITIAL CALIBRATION 19
- Scrubber 25
- SAMPLE CHAMBER 25
- 6.2. OPERATING MODES 28
- Mode Field 29
- 6.2.2. TEST FUNCTIONS 30
- RANGE CONFIGURATION 31
- FOR SINGLE RANGE MODE 33
- FOR DUAL RANGE MODE 34
- FOR AUTO RANGE MODE 35
- 05514 Rev A1 31 39
- DIAGNOSTICS FUNCTIONS 41
- AIO Configuration Submenu 43
- 6.7.4. HESSEN PROTOCOL 47
- CALIBRATION PROCEDURES 49
- EPA PROTOCOL CALIBRATION 51
- INSTRUMENT MAINTENANCE 53
- WARM-UP 55
- THEORY OF OPERATION 57
- 10.2. PNEUMATIC OPERATION 58
- 10.2.3. THE NAFION 59
- DRYER 59
- 10.3. ELECTRONIC OPERATION 61
- 10.3.2. THE RELAY PCA 62
- M300EU THEORY OF OPERATION 63
- 10.3.2.3. Status LED’s 64
- 10.3.3.1. A to D Conversion 64
- 10.3.3.2. Sensor Inputs 64
- TROUBLESHOOTING & REPAIR 67
- 05514 Rev A1 61 69
- (As Displayed) 71
- INDICATED FAILURE(S) 71
- 05514 Rev A1 63 71
- 11.3. GAS FLOW PROBLEMS 73
- OVEN HEATER K3 YES 74
- 11.5.2.1. A/D Functions 74
- A-2 05924 Rev K.6 78
- 05924 Rev K.6 A-3 79
- Æ iDAS Submenu 80
- Æ COMM and VARS Submenus 81
- Æ Hessen Protocol Submenu 82
- PASSDAS RNGE CLK MORE 83
- COMM VARS 83
- ZERO_LIMIT Ratio 1.15 0–5 84
- CO2_RANGE 86
- USER NOTES 94
Související produkty a manuály pro Měření, testování a kontrola Teledyne 300EU
(86 stránky)
(42 stránky)Great-planes F-20 Tigershark Electric Ducted Fan Rx-R - GPMA601 manuals
Owner’s manuals and user’s guides for Air equipment Great-planes F-20 Tigershark Electric Ducted Fan Rx-R - GPMA601.
We providing 1 pdf manuals Great-planes F-20 Tigershark Electric Ducted Fan Rx-R - GPMA601 for download free by document types: User Manual
Komentáře k této Příručce