Teledyne 360E Uživatelský manuál Strana 52
- Strana / 282
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Optional Hardware and Software Model 360E Instruction Manual
5.2.1. Converting Current Loop Analog Outputs to Standard Voltage
Outputs.
NOTE
Servicing or handling of circuit components requires electrostatic discharge protection,
i.e. ESD grounding straps, mats and containers. Failure to use ESD protection when
working with electronic assemblies will void the instrument warranty.
See Chapter 12 for more information on preventing ESD damage.
To convert an output configured for current loop operation to the standard 0 to 5 VDC output operation:
4. Turn off power to the analyzer.
5. If a recording device was connected to the output being modified, disconnect it.
6. Remove the top cover
Remove the set screw located in the top, center of the rear panel
Remove the screws fastening the top cover to the unit (four per side).
Lift the cover straight up.
7. Disconnect the current loop option PCA from the appropriate connector on the motherboard (see Figure
5-1).
8. Place a shunt between the leftmost two pins of the connector (see Figure 5-1).
6 spare shunts (P/N CN0000132) were shipped with the instrument attached to JP1 on the back of the
instruments keyboard and display PCA
9. Reattach the top case to the analyzer.
10. The analyzer is now ready to have a voltage-sensing, recording device attached to that output
5.3. Expendable Kits (Options 42C, 42D and 43)
OPTION NUMBER DESCRIPTION
OPT 42C
1 year’s supply of replacement of 47mm dia. particulate filters
OPT 42D 1 full replacement’s volume of indicating soda-lime for the external CO
2
scrubber
included with options 51 & 53 (approximate active lifetime: 1 year)
OPT 43
Options 42 C & 42D
40 05232 Rev B3
- MODEL 360E 1
- CARBON DIOXIDE ANALYZER 1
- SAFETY MESSAGES 3
- TABLE OF CONTENTS 5
- 2 Rev B3 v 7
- 2 Rev B3 vii 9
- LIST OF APPENDICES 10
- LIST OF FIGURES 10
- LIST OF TABLES 11
- User Notes 12
- 1. M360E DOCUMENTATION 13
- 2.1. Specifications 15
- 2.2. CE Mark Compliance 16
- 2.3. Warranty 16
- 3. GETTING STARTED 19
- Back of the instrument 20
- 3.1.1. M360 Layout 21
- (+5 VDC; 15VDC) 22
- (+12 VDC) 22
- 3.1.2.1. Power Connection 24
- 3.1.2.2. Output Connections 25
- 3.2. Initial Operation 35
- 3.2.2. Warm Up 36
- 3.2.3. Warning Messages 36
- 3.2.4. Functional Check 38
- 05232 Rev B3 29 41
- 3.3.1. Initial O 42
- 4.1. FAQ’s 47
- 4.2. Glossary 48
- OPTION NUMBER DESCRIPTION 51
- Outputs 52
- (Normal State) 53
- 5.5. Communication Options 56
- 5.5.3. Ethernet (Option 63) 57
- 5.6. Oxygen Sensor (OPT 65) 58
- Sensor 59
- 5.7. Additional Manuals 60
- 6. OPERATING INSTRUCTIONS 63
- 6.2. Sample Mode 64
- 6.2.2. Warning Messages 67
- 6.3. Calibration Mode 68
- 6.4. SETUP MODE 69
- Information 70
- 6.7.1. iDAS Structure 71
- 6.7.1.1. iDAS Channels 72
- 6.7.1.2. iDAS Parameters 73
- 6.7.2. Default iDAS Channels 74
- LIST OF CHANNELS 75
- LIST OF PARAMETERS 75
- 05232 Rev B3 65 77
- DATA ACQUISITION 78
- 6.7.2.3. Trigger Events 79
- Press SET> key until… 80
- 05232 Rev B3 69 81
- 05232 Rev B3 71 83
- 6.7.2.6. Number of Records 84
- Configuration 89
- 6.8.2. Reporting Range Modes 90
- PRIMARY SETUP MENU 91
- PRIMARY SETUP MENU 93
- 6.8.6. Range Units 94
- 6.8.7. Dilution Ratio 95
- See Table 6-8 for 96
- Passwords and Levels 96
- Communication Ports 98
- Male DB-9 (RS-232) 99
- Female DB-9 (COM2) 99
- CN3 & CN4 100
- COM2 – RS-485 101
- COM2 – RS-232 101
- COM1 – RS-232 101
- 92 05232 Rev B3 104
- LED FUNCTION 105
- PRIMARY SETUP MENU 107
- 05232 Rev B3 97 109
- Contact your IT Network 110
- Administrator 110
- Multidrop 111
- RS-232 port 112
- 6.11.8. COM Port Baud Rate 113
- 6.11.9. COM Port Testing 114
- STABIL_GAS 115
- 104 05232 Rev B3 116
- Front Panel 117
- Mode Indicator 117
- 6.13.2. Signal I/O 118
- ANALOG OUT 121
- ENTR accepts the new setting 124
- See Table 3-1 for 125
- 6.13.4.5. AIN Calibration 128
- 6.13.5. Electric Test 129
- for Measurement signal 130
- 6.13.7. Pressure Calibration 131
- 6.13.8. Flow Calibration 132
- 6.13.9. Test Channel Output 133
- Alarms 134
- 6.15.1.1. Status Outputs 135
- 124 05232 Rev B3 136
- 6.15.1.2. Control Inputs 137
- 6.15.2.3. Command Syntax 139
- 6.15.2.4. Data Types 139
- 6.15.2.5. Status Reporting 140
- Parameter Standard Hessen 144
- 6.15.4.8. Instrument ID Code 148
- 7. CALIBRATION PROCEDURES 149
- Calibrated 150
- VENT here if input 150
- Continue Calibration as per 159
- Standard Procedure 159
- To program the Sequence: 162
- 150 05232 Rev B3 162
- 7.7. Calibration Quality 163
- 8. EPA PROTOCOL CALIBRATION 165
- 9.1. Maintenance Schedule 167
- Warm-up 169
- 9.3. Maintenance Procedures 171
- 9.3.3.2. Pressure Leak Check 172
- 10.1. Measurement Method 175
- 10.1.3.1. The GFC Wheel 176
- Chamber 178
- 10.1.4.1. Ambient CO 179
- Interference Rejection 179
- 10.2. Pneumatic Operation 180
- 10.2.2. Flow Rate Control 181
- 10.2.4. Particulate Filter 182
- 10.2.5. Pneumatic Sensors 182
- 10.3. Electronic Operation 183
- PC 104 Bus 184
- 10.3.2. CPU 185
- 10.3.3.3. GFC Wheel 186
- 10.3.3.4. IR Photo-Detector 187
- 10.3.4.1. Overview 187
- ACTIVE WHEN: DESIGNATION 189
- D2 Segment Sensor 189
- 10.3.5. Relay Board 190
- STATUS LED’s 191
- DC VOLTAGE TEST 191
- RELAY PCA 191
- PN 04135 191
- C Watch Dog Circuitry 192
- 10.3.6.4. Analog Outputs 193
- 10.3.7. I 194
- C Data Bus 194
- 10.4. Interface 196
- 10.4.1.2. Keyboard 197
- 10.4.1.3. Display 197
- Key Press 198
- C to/from CPU 198
- 10.5. Software Operation 200
- INDICATED FAILURE(S) 207
- 05232 Rev B3 195 207
- Mother Board 209
- P/N 04069 209
- 05232 Rev B3 199 211
- 11.2. Gas Flow Problems 212
- SAMPLE CHAMBER 213
- 11.2.2.1. Flow is Zero 214
- 11.2.2.2. Low Flow 215
- 11.2.2.3. High Flow 215
- 11.3. Calibration Problems 216
- 11.4.1.2. Bench Temperature 218
- 11.4.2. Excessive Noise 220
- 11.5. Subsystem Checkout 221
- 11.5.3. I 222
- 11.5.5. Relay Board 223
- 11.5.6. Sensor Assembly 223
- 11.5.6.3. GFC Wheel Drive 224
- 11.5.6.4. IR Source 224
- 11.5.7. Motherboard 225
- 11.5.7.4. Status Outputs 227
- 11.5.8. CPU 228
- 11.6. Repair Procedures 230
- 10-25% RH 233
- Wrist Strap 235
- P rotective M a t 235
- Ground Point 235
- DO NOT use pink-poly bags 239
- User Notes: 239
- USER NOTES: 240
- A-2 05233 Rev G.4 242
- 05233 Rev G.4 A-3 243
- A-4 05233 Rev G.4 244
- (iDAS) 245
- 05233 Rev G.4 A-5 245
- A-6 05233 Rev G.4 246
- 05233 Rev G.4 A-7 247
- A-8 05233 Rev G.4 248
- 3 Rev G.4 A-9 249
- A-10 05233 Rev G.4 250
- 05233 Rev G.4 A-11 251
- A-12 05233 Rev G.4 252
- 05233 Rev G.4 A-13 253
- A-14 05233 Rev G.4 254
- 05233 Rev G.4 A-15 255
- A-16 05233 Rev G.4 256
- 05233 Rev G.4 A-17 257
- A-18 05233 Rev G.4 258
- 05233 Rev G.4 A-19 259
- A-20 05233 Rev G.4 260
- 05233 Rev G.4 A-21 261
- A-22 05233 Rev G.4 262
- 05233 Rev G.4 A-25 265
- A-26 05233 Rev G.4 266
- 05233 Rev G.4 A-27 267
- A-28 05233 Rev G.4 268
- 05233 Rev G.4 A-29 269
- A-30 05233 Rev G.4 270
- 05234 Rev B B-1 273
- M360E Spare Parts List 275
- Model 360E 277
- Warranty/Repair 279
- Questionnaire 279
- D-2 05236 Rev C 282
Související produkty a manuály pro Měření, testování a kontrola Teledyne 360E
(114 stránky)
(42 stránky)Makita HR4500C (MJ) manuales
Manuales del propietario y guías del usuario para Herramientas Eléctricas Makita HR4500C (MJ).
Ofrecemos 1 manuales en pdf Makita HR4500C (MJ) para descargar gratis por tipos de documentos: Manual de usuario
Komentáře k této Příručce