Portable Oxygen Monitor Teledyne Analytical Instruments i OPERATING & SERVICE INSTRUCTIONS FOR MX300 PORTABLE OXYGEN MONITOR
Introduction MX300 Teledyne Analytical Instruments 2 A sensor failure alarm is incorporated which warns the user if the sensor signal is lost or low
Portable Oxygen Monitor Introduction Teledyne Analytical Instruments 3 NOTE: IF THE LOW ALARM CONDITION IS TRIGGERED WITH THE OXYGEN LEVEL STAYI
Introduction MX300 Teledyne Analytical Instruments 4 Rugged high impact ABS plastic construction Splash resistant case. Long life class R17
Portable Oxygen Monitor Introduction Teledyne Analytical Instruments 5 The Class R17MED oxygen sensor is a disposable sensor. The sen-sor has a c
Introduction MX300 Teledyne Analytical Instruments 6 THE MX300 OXYGEN MONITOR, R17MED OXYGEN SEN-SOR AND ASSOCIATED HARDWARE ARE INTENDED FOR USE AS
Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 7 Operating Instructions Notes: Upon receipt, INSPECT THE ENTIRE
Operating Instructions MX300 Teledyne Analytical Instruments 8 Warning: The MX300 oxygen Monitor, R17MED oxygen sensor, and associated ha
Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 9 Note: Do not use the plastic flow diverter with the R17MED senso
Operating Instructions MX300 Teledyne Analytical Instruments 10 To install V-Mount Adapter, remove the battery compartment door by pry-ing up the h
Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 11 3. Install 3 “AA” alkaline batteries into the holder as shown i
MX300 Teledyne Analytical Instruments ii Copyright © 2009 Teledyne Analytical Instruments. All Rights Reserved No part of this manual may be reprod
Operating Instructions MX300 Teledyne Analytical Instruments 12 play flashing 00.0. Only the CAL and ON/OFF (I/O) keys are functional at this point
Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 13 Note: At the end of the calibration countdown, the Monitor will
Operating Instructions MX300 Teledyne Analytical Instruments 14 1. To set the HI alarm: Press the HI ALARM SET key once. Press the UP and DOWN ar
Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 15 2.1.6 Output 0-1 VDC or RS232 The MX300 Portable Oxygen Monitor
Operating Instructions MX300 Teledyne Analytical Instruments 16 RS232 signal output has been tested with Windows Hyperterminal. The setup changes w
Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 17 2.2 Operation 2.2.1 Procedure Note: Prior to every use, always t
Operating Instructions MX300 Teledyne Analytical Instruments 18 2.3 Factors Affecting Sampling Accuracy 2.3.1 Humidity Humidity does not directly a
Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 19 When a ventilator is a part of the breathing system, the alterna
Operating Instructions MX300 Teledyne Analytical Instruments 20 Error Helium 50%, balance O2 0% Nitrous Oxide 80%, balance O2 0% Carbon Dioxide
Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 21 2.3.6 Cleaning The MX300 and R17MED sensor are non-sterile devic
Portable Oxygen Monitor Teledyne Analytical Instruments iii About This Manual This Manual describes the installation, configuration, operati
Operating Instructions MX300 Teledyne Analytical Instruments 22 Perform alarm test before each use (press the ALARM TEST key). Use only isopr
Portable Oxygen Monitor Service Instructions Teledyne Analytical Instruments 23 Service Instructions 3.1 General Service Information Without acces
Service Instructions MX300 Teledyne Analytical Instruments 24 3.4 Sensor Maintenance DO check the sensor for damage or leaks before use. DON’T imme
Portable Oxygen Monitor Service Instructions Teledyne Analytical Instruments 25 Table 3-1 Troubleshooting Symptom Why What To Do New sensor resp
Service Instructions MX300 Teledyne Analytical Instruments 26 Symptom Why What To Do C) The sensor output has fal-len to a level where it is no
Portable Oxygen Monitor Service Instructions Teledyne Analytical Instruments 27 Symptom Why What To Do C) Calibrate. Note: In the event that n
Service Instructions MX300 Teledyne Analytical Instruments 28 50 5 The ADC circuit failed during POST. 6 (5) 6 (There is no indication of which
Portable Oxygen Monitor Appendix Teledyne Analytical Instruments 29 3.11 Return Authorization for Service For any service beyond sensor and batte
Appendix MX300 Teledyne Analytical Instruments 30 Appendix A.1 Specifications Range: 0-100% oxygen Accuracy: +2% of full scale (at constant temp
Portable Oxygen Monitor Appendix Teledyne Analytical Instruments 31 Left intentionally blank
MX300 Teledyne Analytical Instruments iv Safety Messages Your safety and the safety of others are very important. Please care-fully read and unders
Appendix MX300 Teledyne Analytical Instruments 32 A.2 Spare Parts List QTY PART NO DESCRIPTION 1 C43690-R17MED Micro-Fuel Cell R17MED with flow d
Portable Oxygen Monitor Appendix Teledyne Analytical Instruments 33 Orders should be sent to: TELEDYNE Analytical Instruments 16830 Chestnut Stre
Portable Oxygen Monitor Teledyne Analytical Instruments v Table of Contents Safety Messages ...
MX300 Teledyne Analytical Instruments vi 2.3.3 Pressure ... 182.3.4 Di
Portable Oxygen Monitor Teledyne Analytical Instruments vii List of Figures Figure 1-1: MX300 Front View ...
MX300 Teledyne Analytical Instruments viii List of Tables Table 2-1: Oxygen Reading Error in a Mixture of Anesthetic Gas . 19Table 3-1 Troubleshoo
Portable Oxygen Monitor Introduction Teledyne Analytical Instruments 1 Introduction The Teledyne Analytical Instruments MX300 Oxygen Monitor, he-
Komentáře k této Příručce